Mechatronic systems and materials 2010 : selected papers / ed

Mechatronic systems and materials 2010 : selected papers / ed

Mechatronic systems and materials 2010 : selected papers / ed. Ewald
Macha, Roland Pawliczek. – Opole, 2011
Spis treści
CONTENTS
Preface
5
Alexandra-MariaALUTEI, Beniamin CHETRAN, Dan MANDRU
Development of an interface for refreshable Braille devices
7
Mounir AMOKRANE, Eric DUHAYON
Characterization of ferromagnetic silicones for flexible actuation concept –
illustration with integrated coils in membranes
13
Katarzyna BIAŁAS
Kinematic excitations in active reduction of vibrations
27
Cem BOGA, Erdogan SІМSЕК, Huseyin BULGURCU
Torsional vibration analysis of multi shaft-disc systems
37
Huseyin BULGURCU
A case study: designing of multi process control trainer for mechatronic
education
51
Ahmet QOS GUN, Cemal OKUYAN, Nafel DOGDU
Biocompatibility investigation of steel 420 in plasma (Human body oil)
63
P. GU, R. GUNDERSEN, A.O. KALVIK, R. SALVESEN, H.R. KARIMI, M. OTTESTAD
Data gathering for pitch stabilization of a high speed catamaran
69
Riza GURBUZ, Mehmet Ali DONERTAS, Hayati MAMUR
Experimental torque-speed analysis of selected AC servo motors
for desk-top NC milling machine
81
Tatjana IVANOVA, Janis RUDZITIS
Mass measurement interlaboratory comparison in Latvia
89
Zbigniew KNEBA, Jacek KROPIWNICKI
Oxygen sensor delay time in exhaust system
99
Artur KOPCZYŃSKI, Eugeniusz RUSIŃSKI, Jacek KARLIŃSKI
Axial compression of spot welded longitudinal beams
109
Jacek KROPIWNICKI, Zbigniew KNEBA
Phenomenological correction of height above ground level of vehicle
derived from GPS system
117
Vigantas KUMSLYTIS, Algirdas Vaclovas VALIULIS, Raimondas SKINDARAS
Effect of post-weld heat treatment on the structure of 5%Cr-0.5%Mo
steel welded joints
127
Ion LUNGU; Dan MANDRU, Simona NOVEANU
Measurement of the shape memory alloy wires parameters
137
Ion LUNGU, Dan MANDRU, Simona NOVEANU
Circuit board for a linear actuator with SMA wires
145
Zdenek MAJER, Eva NOVOTNA
Numerical estimation of the tensile properties of the composite with rigid
particles
151
Dan MANDRU, Ion LUNGU, Simona NOVEANU, Olimpiu TATAR
Product dissection as a method for learning mechatronics
159
Vadim MOKSHIN, Vladas VEKTERIS
Effectiveness of liquid crystal as cutting fluid additive
169
Gatis MUIZNIEKS, Eriks GERINS, Janis OZOLINS, Vineta MUIZNIECE
Analysis of providing rotor surface resistance to wear
179
Aleksey MURZINTSEV
Modelling of an electromagnetic drive gear of an automobile braking system
with indemnification of deterioration of brake pads
187
Simona NOVEANU, Dan MANDRU, Ion LUNGU, Veneel CSIBI, Dan NOVEANU
Experimental research of a mini-system with piezoelectric actuation
191
Krzysztof PUCHER, Dariusz POLOK
Application of single-board with the embedded DOS operating system as
central units of data acquisition system used for mechatronic measurements
199
Larisa RYBAK, Viktor ERZHUKOV, Elena GAPONENKO
Design of kinematic and dynamic model 6-DOF parallel robot
209
Tadeusz SMOLNICKI, Paweł MAŚLAK
Experimental identification of loads in multi-caterpillar mechanism
of the ride of dumping conveyor
219
Olimpiu TATAR, Claudiu CIREBEA, Adrian ALUTEI, Dan MANDRU
Driving modules with adaptable structure for in pipe inspection modular
robotic systems
229
Oleg TOKMACHOV
Economic aspects of laser processing in machinery and apparatus building
243
Rymantas Tadas TOLOCKA
Mechanical engineering and mechatronics: development of study programmes
249
Andrzej WRÓBEL
Influence of piezoelectric plates number in stack on characteristics of
mechatronic system
255
Indeks of authors
263
oprac. BPK